Topographic surveys · Spot-height plans · DTM

Topography and topographic surveys

Measuring the land as it is, before transforming it.

A topographic survey is the starting point of every project: it describes the shape of the land, its elevations, its boundaries and everything on it. Without it, an architect designs in a vacuum and a contractor excavates by guesswork.

MAPTOPO carries out surveys tied in to the project’s coordinate system, checked and delivered in formats that design offices can use straight away.

Expertise

What is a topographic survey?

A topographic survey measures in the field the position (X, Y) and elevation (Z) of characteristic points: boundary corners, kerbs, buildings, trees, visible utilities, breaks of slope. These points, computed and checked in the office, produce a topographic plan with spot heights that faithfully represents existing conditions.

Depending on the size of the site and the accuracy required, measurements are taken with real-time GNSS, a total station, a level for the finest elevations, or a drone for large areas. The choice of method depends on the required accuracy, the size of the site, the timeframe and site access.

The result is more than a drawing: it is a reliable geometric base on which design, permits, quantity take-offs and the setting out of future structures all depend.

Applications

  • 01

    Spot-height plan and existing conditions

    2D representation of the land and its features, with elevations, for architectural, urban planning and road design studies.

  • 02

    Site plan

    Positioning a project within its surroundings: boundaries, access, neighbouring buildings, visible easements.

  • 03

    Digital terrain model

    Continuous surface computed from surveyed points, the basis for contour lines, profiles and volume calculations.

  • 04

    Longitudinal profiles and cross-sections

    Sections of the ground along an alignment or perpendicular to it, essential for road, canal and utility network design.

  • 05

    Levelling

    Precise determination of elevations and gradients for gravity networks, slabs and sensitive structures.

  • 06

    Regulated measurements

    Measurements of distances and areas governed by regulations, supported by a plan and a certificate.

Methodology

  1. Step 01

    Scoping

    Defining the survey extent, required accuracy, coordinate system and deliverables with the project owner.

  2. Step 02

    Control network and tie-in

    Establishing reference points on site and tying them in to the project’s coordinate system.

  3. Step 03

    Field survey

    Measuring detail points with GNSS, a total station or a level, depending on the area and target accuracy.

  4. Step 04

    Computation and checks

    Processing observations, checking loop closures and duplicate points, verifying the consistency of the plan.

  5. Step 05

    Plotting and delivery

    Drafting the plan, computing the DTM and contours, issuing signed digital and paper deliverables.

Deliverables

  • Topographic plan with spot heightsDWG/DXF and PDF format, at the requested scale.
  • Digital terrain modelPoint set, triangulation and contour lines.
  • ProfilesLongitudinal profiles and cross-sections along the alignment at defined intervals.
  • Point listingX, Y, Z coordinates of surveyed points and benchmarks.
  • Survey reportMethod, coordinate system, accuracy and any reservations.

Technologies

  • GNSS RTKReal-time centimetre-level positioning in open areas.
  • Total stationAngle and distance measurement for fine detail and obstructed areas.
  • LevelPrecise elevations for gradients and sensitive structures.
  • Photogrammetry droneFast coverage of large sites.

Project types

  • Building plots
  • Housing developments
  • Buildings
  • Roads and tracks
  • Business parks
  • Industrial sites
  • Agricultural projects
  • Solar sites

For the project owner

  • Design based on real conditions

    Studies start from the measured land, not from an old or approximate plan.

  • Fewer surprises on site

    Knowing gradients, elevations and footprints in advance limits rework and cost overruns.

  • Ready-to-use files

    Plans and models delivered in the formats used by design offices and contractors.

Technical terms

Spot-height plan (plan coté)
A plan of the land showing the elevations of surveyed points and features.
DTM (MNT)
Digital terrain model: a continuous surface of the natural ground, without buildings or vegetation.
Contour line
A line joining points of equal elevation; the vertical spacing between two contours is the contour interval.
Control network
A set of marked reference points on which all site measurements are based.
Tie-in
The operation that links a local survey to an official coordinate system or to the project system.
Planimetry / altimetry
The horizontal position (X, Y) of a point on the one hand, its elevation (Z) on the other.

Frequently asked questions

When should a topographic survey be carried out?

Before any design work: buying land, applying for a building permit, road or utility studies, a housing development project. It is the input data that determines the accuracy of everything that follows.

What is the difference between a spot-height plan and a boundary plan?

A spot-height plan describes the shape and features of the land with its elevations. A boundary plan establishes and physically marks the legal limits of a property. Both can be produced during the same site visit.

What documents are needed for a survey?

Generally: identification of the land (land title or reference), a location plan, the area to be surveyed and the intended use of the plan. The required coordinate system is specified if the project imposes one.

In what format is the plan delivered?

Usually in DWG or DXF for design software, together with a signed PDF. Other formats can be supplied according to the design office’s needs.

Related services

Quote request

Tell us about your project. We will come back to you with a proposal for the assignment.